Austria, Germany, France, Italy, Korea, 5. Headlight Circuit Relay 7. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website.
These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
This website uses cookies to improve your experience. Rim Inspection Axle Inspection Balance Inspection Axial 0. If there is any damage to the rim, it must be replaced. Adjust the tire air pressure according to the specifications if necessary. Air Pressure when cold Up to This can damage or warp the disc. Place blocks under the wheel so that the disc does not touch the ground.
Chain Slack — — — Standard Chain Make Enuma — A chain that breaks or jumps off the sprock- ets could snag on the engine sprocket or lock the rear wheel, severely damaging the motorcycle and causing it to go out of control.
Link Pin Outside Diameter 5. Standard: 5. If the bearing is removed, it will need to be replaced with a new one. T3: 1. R: Replacement Parts Disc Thickness 4. Disc Runout Not more than 0. Brake Fluid: Grade If you apply com- pressed air into the caliper, the piston may crush your hand or fingers.
There is a flat washer [D] on each side of the hose fitting. If the fluid level is lower than the lower level line, fill the reservoir to the upper level line [A] in the reservoir [B]. Air, however, is easily compressed. Never reuse old brake fluid. Do not use fluid from a container that has been left unsealed or that has been open for a long time. If it does not, adjust the rear brake cam lever angle. Shoe Lining Thickness 4. Drum Inside Diameter If necessary, measure the oil level as follows.
The slit [D] in the bushing must face toward the left or right. Replace them if necessary. If the spring of either fork leg is shorter than the service limit, it must be replaced. L: Apply a non-permanent locking agent. The front wheel should swing fully left and right from the force of gravity until the fork hits the stop.
Starter Lockout Switch 8. Turn Signal Relay Side Stand Switch 2. Water Temperature Switch 9. Battery Ignition Coils Horns Junction Box 4. Spark Plugs Fan Switch Front Brake Light Switch 5. Ignition Switch 2.
Water Temperature Switch 3. Radiator Fan 4. Fan Switch 5. Ignition Coils 6. Spark Plugs 7. Rear Brake Light Switch 8. Alternator Stator 9. Crankshaft Sensor Starter Motor Starter Lockout Switch 2. Front Brake Light Switch 3.
Horns T1: 1. Junction Box 3. Turn Signal Relay 4. Battery 5. IC Igniter T1: 5. Learn and ob- serve all the rules below. This will burn out the diodes in the electrical parts. If any wiring is in poor condition, replace the damaged wiring. If the specific gravity is below 1. If the battery is charged while still in- stalled, battery electrolyte may spill and corrode the frame or other parts of the motorcycle. To turn off the headlight of United States and Canada models disconnect the headlight connector.
The readings should show nearly battery voltage when the en- gine speed is low, and, as the engine speed rises, the readings should also rise. A short or open in one of the coil wires will result in either a low output or no output at all. Refer to the ap- propriate chapters and Charging System Wiring Diagram. Do not touch the spark plugs, ignition coils, or spark plug leads while the engine is running, or you could receive a severe electrical shock. Note the following. A tester other than the Kawasaki Hand Tester may show different readings.
If a megger or a meter with a large-capacity battery is used, the IC igniter will be damaged. Junction Box 7. Ignition Fuse 10 A Main Fuse 30 A 2. Ignition Switch 8. Diodes Battery 3. Engine stop Switch 9. Neutral Switch IC Igniter 4. Starter Button Replace the starter motor with a new one if the commu- tator diameter is less than the service limit. If there is not close to zero ohm, the brush plate has an open.
Ignition Switch 6. Starter Circuit Relay Starter Motor 2. Engine Stop Switch 7. Ignition Fuse 10A Starter Relay 3.
Starter Button 8. Starter Lockout Switch Main Fuse 30A 4. In these models, the headlight does not go on when the igni- tion switch and the engine stop switch are first turned on. The headlight comes on after the starter button is released and stays on until the ignition switch is turned off.
Dimmer Switch 2. High Beam Indicator Light 9. Alternator 3. Headlight Main Fuse 30 A 4. Junction Box City Light 6. Headlight Circuit Relay If any spring is shorter than the service limit, it must be replaced.
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website.
These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies.
But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information. Skip to content. This website uses cookies to improve your experience.
0コメント